The Best Universal Dishwasher Side Mounting Bracket

This undercounter mounting bracket for dishwashers is for solid surfaces like granite. Works with all standard size dishwashers. Can also be used on all stainless and plastic tall tub platforms.

Product Description

Allows mounting of dishwasher to side of cabinet.

From the Manufacturer

Allows mounting of dishwasher to side of cabinet.

1) Turn off power to your dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) 2) Rotate lower access panel fasteners and remove them 3) Remove access panel/sound dampening pad. Determine if the water supply/power lines have enough slack to move the dishwasher. If not, you will need to turn off water supply valve, disconnect water supply line from inlet valve & release power line from junction box 4) Open dishwasher door, remove the screws from the existing brackets (if present) 5) You will next be moving the dishwasher. To do so, you may need to lower the dishwasher by adjusting the leveling legs 6) Carefully pull dishwasher a few inches away from the front of the cabinet 7) Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets 8) Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place 9) Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary). Replace the screws in your new brackets 10) Reverse steps 3, 2 and 1. ALL SET! This is a generic product manufactured and distributed by Impresa Products (TM). This is not a Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) or Inglis (TM) OEM product and Impresa Products has no affiliation with or endorsement from these brands. Our product is not covered under any other manufacturer’s warranty (except for Impresa Products). The Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names and logos are the registered trademarks of their owners. Any use of the Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names, model or any other related designations are made solely for purposes of describing and illustrating compatibility.

2 Packs 8212560 dishwasher side brackets and 4 packs installation screws and 2 packs 8269145 dishwasher upper mounting brackets and 2 packs installation screws

8212560 Dishwasher side mounting bracket:
Material: metal
Quantity: 2 packs mounting brackets and 4 pieces install screws
Replace for part No.: 1201084, AP3953705
Color: black

8269145 Dishwasher upper mounting bracket:
Material: metal
Quantity: 2 packs upper mounting brackets and 2 packs install screws
Replace for part No.: WP8269145, WP8269145VP
Color: sliver

Practical to use:
Compatible with various most top name brands such as KitchenAid, Kenmore, Maytag, Amana, Jenn-Air, Estate, Magic Chef, Inglis, Roper.

Features:
Good quality and can be applied for a very long time.

Package includes:
2 x 8212560 Dishwasher side mounting bracket
4 x Installation screws
2 x 8269145 Dishwasher upper mounting bracket
2 x Silver installation screws

Warmly note:
Not original parts, the mention of any related models and brands above is only for purposes of demonstrating compatibility.

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) and turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw or one of new provided screws. 4) Push dishwasher back into place. Open dishwasher door. Determine which bracket hole you will use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If you need to use back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher back into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in the tub. Use a sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 inch hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a nice clean hole without damaging the tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into the cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal. This is a generic product manufactured & distributed by Impresa Products (TM). This is not a Frigidaire (TM) / Electrolux (TM) OEM product. Any use of Frigidaire (TM) or Electrolux (TM) brand names, models, etc. are made solely to describe & illustrate compatibility.

• Brackets for Installing Dishwasher Beneath Countertop of Granite or Other Impervious Material

SPECIFICATIONS
Works with the following models:
8212560 : Kenmore – 665.12833K311, 665.13253K110, 665.13922K010, 665.13923K010,etc.
8269145: Kenmore – 665.12776K311, 665.12782K311, 665.12833K311, 665.13173K705,etc.

Replaces part numbers:
8212560 replaces 120108, AP3953705.
8269145 replaces WP8269145, WP8269145VP

Works with most top name brands: Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Jenn-Air, Estate, Magic Chef, Inglis, Crosley, Roper

Fixes the following symptoms:
Door latch failure
Door won’t close

Count on our 8212560 & 8269145 Dishwasher Side Mounting Bracket Kit With Screws for an unrivaled mix of durability, convenient functionality, and great value for money. Click ‘Add to Cart’ now!

If you are unsure our replacement part will fit your appliance model, you can ask us in Customer questions & answers section or contact us by visiting the Blue Stars LLC storefront — click the “Blue Stars LLC” on a product page to get to the storefront — then click the “Ask a question” link under Further Information. Select your reason, and then tell us about the question.

The Whirlpool brand names and logos are the registered trademarks of their respective owners. Any use of the Whirlpool brand name or model designation for this product is made solely for purposes of demonstrating compatibility

Replaces the following part numbers:
WP8269145, WP8269145VP.

Works for brands:
KitchenAid, Whirlpool, Kenmore, Maytag, Jenn-Air, Amana, Estate, Magic Chef, Inglis, Crosley, Roper.

Fixes problem with:
Door latch failure.
Door won’t close.

Contact Us
If you are not sure if part is correct, ask us in Customer questions & answers section or contact us by visiting the Discount Parts Direct storefront.

Business Wholesale
We are a small local company from Houston, Texas offer discount parts for retail and wholesale. If you need to purchase parts for business , please contact us for lower rates.