The Best Samsung Dishwasher Side Mount Brackets

Genuine Original Equipment Manufacturer (OEM) parts! Door latch and switch DD81-01629A is an original equipment manufacturer (OEM) part that fits some Samsung DW80-series dishwashers. Door latch and switch DD81-01629A holds the dishwasher door shut and includes the door switch. The door switch detects when the door is closed so the dishwasher can start. Unplug the dishwasher and remove the T20 Torx screws from the inner door panel, and then separate the inner and outer door panels to access the door switch. Model numbers this part fits: DW80F600UTB/AA-0000, DW80F600UTB/AA-0001, DW80F600UTS/AA-0000, DW80F600UTS/AA-0001, DW80F600UTW/AA-0000, DW80F600UTW/AA-0001, DW80F800UWS/AA-0000, DW80F800UWS/AA-0001, DW80J3020UB/AA-0000, DW80J3020US/AA-0000, DW80J3020UW/AA-0000, DW80K5050UB/AA-0000, DW80K5050US/AA-0000, DW80K5050UW/AA-0000, DW80K7050UG/AA-0000, DW80K7050US/AA-0000 For Samsung.

1) Turn off power to your dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) 2) Rotate lower access panel fasteners and remove them 3) Remove access panel/sound dampening pad. Determine if the water supply/power lines have enough slack to move the dishwasher. If not, you will need to turn off water supply valve, disconnect water supply line from inlet valve & release power line from junction box 4) Open dishwasher door, remove the screws from the existing brackets (if present) 5) You will next be moving the dishwasher. To do so, you may need to lower the dishwasher by adjusting the leveling legs 6) Carefully pull dishwasher a few inches away from the front of the cabinet 7) Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets 8) Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place 9) Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary). Replace the screws in your new brackets 10) Reverse steps 3, 2 and 1. ALL SET! This is a generic product manufactured and distributed by Impresa Products (TM). This is not a Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) or Inglis (TM) OEM product and Impresa Products has no affiliation with or endorsement from these brands. Our product is not covered under any other manufacturer’s warranty (except for Impresa Products). The Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names and logos are the registered trademarks of their owners. Any use of the Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names, model or any other related designations are made solely for purposes of describing and illustrating compatibility.

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) and turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw or one of new provided screws. 4) Push dishwasher back into place. Open dishwasher door. Determine which bracket hole you will use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If you need to use back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher back into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in the tub. Use a sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 inch hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a nice clean hole without damaging the tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into the cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal. This is a generic product manufactured & distributed by Impresa Products (TM). This is not a Frigidaire (TM) / Electrolux (TM) OEM product. Any use of Frigidaire (TM) or Electrolux (TM) brand names, models, etc. are made solely to describe & illustrate compatibility.

Genuine Original Equipment Manufacturer (OEM) parts! This flow sensor (part number DD94-01006A) is for dishwashers. Flow sensor DD94-01006A measures the flow of water entering the dishwasher. Unplug the dishwasher or shut off the house circuit breaker before installing this part. Wear work gloves to protect your hands. For Samsung.